• New Woodbarter Hats Are Available!!! Scroll down on the main page to the Member Activities & Site Support, Then click on Wood Barter SCHWAG and go to the topics on hats by Woodtickgreg to order your hat. There's only a limited quanity, so don't wait to get yours.

I need some Olive wood.

LSCG

LSCG

Member
Full Member
Messages
889
Reaction score
1,140
Location
Texas
First name
Zane
I’m in need of some high figured olive wood for an upcoming project.

could probably use a large turning blank or slab and cut down to my needs. or I could use smaller blocks or boards, say 1”-1 1/2”thick by 2 1/2” wide by 5” long.

Thanks!
Zane
 
LSCG said:
I’m in need of some high figured olive wood for an upcoming project.

could probably use a large turning blank or slab and cut down to my needs. or I could use smaller blocks or boards, say 1”-1 1/2”thick by 2 1/2” wide by 5” long.

Thanks!
Zane
Click to expand...
Why are you calling that large? ........... Nubs
 
LSCG said:
What do you mean?
Click to expand...
The sizes your listing are not classified as large in his (and my) mind.

Olive is pretty easy to get a hold of. There should be many online distributors of speciality species around and you will find some here. I could get some for you from here but I’m quite certain that Austrian taxes and shipping would hurt the operation more than any benefit you could achieve from getting the wood from me (assuming there is a benefit to that in the first place)
 
LSCG said:
I’m in need of some high figured olive wood for an upcoming project.

could probably use a large turning blank or slab and cut down to my needs. or I could use smaller blocks or boards, say 1”-1 1/2”thick by 2 1/2” wide by 5” long.

Thanks!
Zane
Click to expand...
Ocooch Hardwoods usually has olive wood listed in the "Handpicked" section. Most of the boards they have are 1" thick and quite a bit larger than 2.5" × 5". If you need a thicker piece, give them a call; they might be able to set up a custom order. I've always gotten good quality and service from them.

Olivewood Wood | Unique Pieces for Specialty Woodworking

ocoochhardwoods.com ocoochhardwoods.com
 
  • Thread Starter Thread Starter
  • #6
daniscool said:
The sizes your listing are not classified as large in his (and my) mind.

Olive is pretty easy to get a hold of. There should be many online distributors of speciality species around and you will find some here. I could get some for you from here but I’m quite certain that Austrian taxes and shipping would hurt the operation more than any benefit you could achieve from getting the wood from me (assuming there is a benefit to that in the first place)
Click to expand...

well if y’all read it again I didn’t call those listed sizes large. I actually called them smaller blocks/boards.
 
LSCG said:
well if y’all read it again I didn’t call those listed sizes large. I actually called them smaller blocks/boards.
Click to expand...
OK, I reread your post. I stand corrected. It's too bad the Olive I have doesn't really show color like some I've had and seen in the past on trunks over 6' diameter. ............. Nubs
 
Nubsnstubs said:
OK, I reread your post. I stand corrected. It's too bad the Olive I have doesn't really show color like some I've had and seen in the past on trunks over 6' diameter. ............. Nubs
Click to expand...
I'm gonna make an edit. The olive I've seen and had did not have 6' OD trunks. They were Burl Balls that Olive has at ground level.
I've seen one in Orange, California that has to be over 8-9 feet at the ground. .......... Nubs
 
You must log in or register to reply here.
Back
Top