*ended* Desert Ironwood for sale

JD1137 said:
Pics attached with sizes. I’m not a knife scale guy, but I blue taped the section where I think you could get some knife scales. 1” thick x 2.25 wide by 5.25” tall. There’s more room than that, but length starts to taper. It’s 3# so, $18 plus shipping. Thanks!
Click to expand...
Sounds good, looks like I could get a block and a set of scales out of that, maybe some accent pieces too. Let me know what the shipping cost is and send me your paypal.
 
  • Thread Starter Thread Starter
  • #22
Bear Custom Builds said:
Sounds good, looks like I could get a block and a set of scales out of that, maybe some accent pieces too. Let me know what the shipping cost is and send me your paypal.
Click to expand...
How about your zip code and I’ll check flat rate vs. pirate shipping
 
  • Thread Starter Thread Starter
  • #23
  • Thread Starter Thread Starter
  • #26
JD1137 said:
I think you’re looking at this piece Eric. Right at 15#. It’s probably the bulkiest in the bunch and most solid. Would be $6/pound so $90 plus shipping. Too big for a flat rate, so if you give me your zip, I can check pirate ship. Measures about 12” long to the tip by about 8 x 8, but of course is wonky angles. Probably closer to an 8 x 8 x 8 block, but I’m selling by weight anyway. Thanks for the interest!
View attachment 245857View attachment 245858View attachment 245859View attachment 245860
Click to expand...
Haven't heard if you have any interest @Eric Rorabaugh ?? Let me know and thanks!
 
  • Thread Starter Thread Starter
  • #30
Mike Hill said:
I don't need a whole or half log, just need a few pieces/chunks that are about half sap and half heart. Anything about 4 to 6" long and not smaller than 1" width
Click to expand...
Hey Mike - @Mike Hill
Have got this one reserved for you if you want it. 12” long x 4” wide down to 3” wide and 1 1/2” thick up to 2” thick. Shown wet. Preliminary weight a little less than 3# so would be $18 (max) plus shipping. Let me know. Thank you.
IMG_3538.webp IMG_3539.webp IMG_3540.webp IMG_3541.webp
 
  • Thread Starter Thread Starter
  • #33
dvoigt said:
How about a piece 3” thick that I could cut a peppermill or 2 out of. Cracks are ok
Click to expand...
@dvoigt
I have this piece that’s pretty sweet. Measures 12” long. Side measurements are 4”, 4” 4” and 3.25” (does that make sense?😳)
Pretty confident you can get a nice 2 3/4 spindle almost the full 12” or real close to 12”. A couple pics are wetted . Weighs right close to 6# so $36 plus shipping.
IMG_3542.jpeg IMG_3543.jpeg IMG_3544.jpeg IMG_3545.jpeg
 
Last edited:
Received the package today, can’t wait to get going on this, big thumbs up John! Thank you!
 
JD1137 said:
@dvoigt
I have this piece that’s pretty sweet. Measures 12” long. Side measurements are 4”, 4” 4” and 3.25” (does that make sense?😳)
Pretty confident you can get a nice 2 3/4 spindle almost the full 12” or real close to 12”. A couple pics are wetted . Weighs right close to 6# so $36 plus shipping.
View attachment 245951View attachment 245952View attachment 245953View attachment 245954
Click to expand...
Looks real nice, I’m going to have to think on it. I don’t like to come on this site because I always want to buy stuff!
 
You must log in or register to reply here.
Back
Top