What free wood did you find today?

Be safe. Those are no fun. I grew up farmi.g and carpentering. Sometimes both at the same time. Pulled several back together. Replace several dozen posts over the years. Put the whole end in a couple 2 stories. Hopefully this is only a single story repair.
Southeast corner on the long roof side, on an off center roof. Got a 100 year old slate roof, rotted out over head. Putting replacement tin up soon. Wanted to replace several rotted hemlock furring strips with W. red cedar. Let's call it a one story with a floor like separation between point A (ground 0) and B (20 feet elevated). Oh, and the floor like thing is rotted from a roof leak so we will be working on a floating temp platform. We don't weigh over 600 so just two red-neck feathers floating in fear having fun.
 
Southeast corner on the long roof side, on an off center roof. Got a 100 year old slate roof, rotted out over head. Putting replacement tin up soon. Wanted to replace several rotted hemlock furring strips with W. red cedar. Let's call it a one story with a floor like separation between point A (ground 0) and B (20 feet elevated). Oh, and the floor like thing is rotted from a roof leak so we will be working on a floating temp platform. We don't weigh over 600 so just two red-neck feathers floating in fear having fun.
Sounds like my northwest wall replace. Only I didn't have slate overhead. I temp shored the floorish thing in mine so I could throw 5/8 plywood on it for a basic scaffold. You all float carefully. And watch that slate!
 
Sounds like my northwest wall replace. Only I didn't have slate overhead. I temp shored the floorish thing in mine so I could throw 5/8 plywood on it for a basic scaffold. You all float carefully. And watch that slate!
Just getting in. We took a 20" diameter Doug-fir utility pole and milled an 8"x 8" replacement beam. Cut replacement tails for several rafters and scabbed them on. Hammered the corner post back in, lagged it to the box beam. Laid several layers of ply down on the floor like thing to jack from, lifted the roof. Cut back the rotted beam to solid and notched the old beam. Cut part of the notch on the replacement section on the mill, and the rest at the barn door. We carried the new beam section in, muscled it up laughing as things made popping noises (both wood and joints). Used timber screws to tie in. I went outside and nailed the siding back on as the rain started dripping off the eves. Luckily still warm, 38 degrees.

Free wood was a few 80' Doug-fir utility poles and one or two 80' Western red cedar poles. These were recently replaced with steel poles (5 years ago).
 
Just getting in. We took a 20" diameter Doug-fir utility pole and milled an 8"x 8" replacement beam. Cut replacement tails for several rafters and scabbed them on. Hammered the corner post back in, lagged it to the box beam. Laid several layers of ply down on the floor like thing to jack from, lifted the roof. Cut back the rotted beam to solid and notched the old beam. Cut part of the notch on the replacement section on the mill, and the rest at the barn door. We carried the new beam section in, muscled it up laughing as things made popping noises (both wood and joints). Used timber screws to tie in. I went outside and nailed the siding back on as the rain started dripping off the eves. Luckily still warm, 38 degrees.

Free wood was a few 80' Doug-fir utility poles and one or two 80' Western red cedar poles. These were recently replaced with steel poles (5 years ago).
I’m whipped….and all I did was read it. Glad you are safe Mark. You are such a good man on so many levels!!!!
 
I didn't realize you had immediate access to a sawmill. That speeds things up a bit.
Timbery sawmill, like a Woodmizer LT 15 sits 85 feet from the barn. Took the tractor up the road 2 miles to get a section of pole. Woodshop is 100 feet from the barn, another direction. So brother has lots of tools to get things done. He is still recovering from a fall a few weeks (4) ago, so I tried to be the muscle today. Only one cow and calf in the barn, opposite corner, lower level. So minimum "spookage".

NO, I do not have immediate access, but sometimes can get him to cut for me. Otherwise we have about 4 portable mills within 2 miles of the house if need be.
 
Timbery sawmill, like a Woodmizer LT 15 sits 85 feet from the barn. Took the tractor up the road 2 miles to get a section of pole. Woodshop is 100 feet from the barn, another direction. So brother has lots of tools to get things done. He is still recovering from a fall a few weeks (4) ago, so I tried to be the muscle today. Only one cow and calf in the barn, opposite corner, lower level. So minimum "spookage".

NO, I do not have immediate access, but sometimes can get him to cut for me. Otherwise we have about 4 portable mills within 2 miles of the house if need be.
Wish I had one mill close to me. The logs I have to pass on.... You saw recycled telephone poles? Run into any hardware?
 
85 feet is immediate access from my point of view...
I drive miles for that 85 feet. Mill is at my brother's place, not my mill. So only get access when he is available, which is rare.
Wish I had one mill close to me. The logs I have to pass on.... You saw recycled telephone poles? Run into any hardware?
Lots of hardware. These big poles have plenty, but it is all very noticeable and not to hard to remove. Often just a few impact guns and sockets. These poles were on lines out in the woods, away from people. Lower section you check over well for trespassing sign nails. Once you get to 10 feet up, mostly clear other than staples for grounding wires and attachment hardware.
 
I meant immediate to the job you were doing. I understood it wasn't yours. It was terribly helpful for the barn job. I have a mill sitting beside my truck and still don't get to use it much. It spent a year and a half at my dad's house 20 minutes away and I only used it 3 times due to weather and our interfering schedule with this darn stuff they call work.
 
Wish I had one mill close to me. The logs I have to pass on.... You saw recycled telephone poles? Run into any hardware?
https://woodmizer.com/us/find-a-local-sawyer good resource for folks looking for sawmills.
In my area I can access 4 mills including my own. People I know and have done business with that live within 4 miles of my house. There are a couple other mills I have dealt with farther away and about a half dozen more in county that I never met but know where the mills are located.
We are overstocked on mills and trees. Live edge slabs start at 40 bucks locally.
100 bucks kiln dried.
 
Last edited:
I’ve been searching for bristlecone!!
If you encounter any you do not need, even small amounts, please let me know!

actually, I’m not picky, so I’ll settle for larger pieces, too. 😁

Thank you for keeping hope alive!
 
What a mess, Douglas fir, juniper, limber pine, bristlecone pine, (pinus aristata) and cottonwood.

View attachment 283364
If you need somewhere to get rid of all those sticks with the knotty swollen areas on them, let me know. I will try to find a dry dark corner to hide them in well away from the "good" wood that you have there...
 
Back
Top