What free wood did you find today?

Nothing fantastic today. I cut almost two loads of Hackberry. Pretty plain Jane all white grain. But one tree had a dark center. Anyone know what causes that? Is it kind of like the dark center in an Ash tree that is dying?

View attachment 285553

I know there's a lot of guys here will cringe when I ask about identifying a tree by its bark. The bark looks a little like Sassafras, but there is no nice smell. Plus, the wood is white. And it's not some type of pine. Any thoughts? Next week in between the rain, I'll try to get a piece.

View attachment 285554
Your Hackberry has grown over branch stubs, these were open wounds that have been grown over. These wounds have infection, infection changes color and smell of the wood.

Looks like Sassafras. When you pop and split the bark, looks like and orange layer. Few trees in the central USA show that. Little sprig on the left looks sassy as well.

Do you have Sourwood in the area?
 
Your Hackberry has grown over branch stubs, these were open wounds that have been grown over. These wounds have infection, infection changes color and smell of the wood.

Looks like Sassafras. When you pop and split the bark, looks like and orange layer. Few trees in the central USA show that. Little sprig on the left looks sassy as well.

Do you have Sourwood in the area?
I thought it was Sassafras too, but when I break off a chunk of bark, there is no root beer smell. I'm curious now, maybe I'll run out there tomorrow and get a chunk.

Sourwood? never heard of it; don't think so. But we'll see.
 
Worse I ever tried to split was a multi crotch piece of honey locust. Wacked on that thing day after day with maul and wedges. Finally threw it aside. A year or two later I built a hydraulic splitter from a massive cylinder Dad brought home from work. Used a piece of railroad track for the slide. Went after that piece of locust again and all it did was twist the railroad iron. Finally threw it in the weeds and let it rot.
 
Worse I ever tried to split was a multi crotch piece of honey locust. Wacked on that thing day after day with maul and wedges. Finally threw it aside. A year or two later I built a hydraulic splitter from a massive cylinder Dad brought home from work. Used a piece of railroad track for the slide. Went after that piece of locust again and all it did was twist the railroad iron. Finally threw it in the weeds and let it rot.
That’s about the time I would have “split” it with a chainsaw!
 
Worse I ever tried to split was a multi crotch piece of honey locust. Wacked on that thing day after day with maul and wedges. Finally threw it aside. A year or two later I built a hydraulic splitter from a massive cylinder Dad brought home from work. Used a piece of railroad track for the slide. Went after that piece of locust again and all it did was twist the railroad iron. Finally threw it in the weeds and let it rot.
Should have used a saw. The slower way to greater accuracy.

That it bent the railroad is unbelievable.
 
Finally used my Alaskan mill for the first time today on some short logs I had picked up, Bois d'Arc & Bradford Pear. It made a small hill of yellow sawdust!

Everything is cut to 3" or 4" thicknesses. Will get it to the bandsaw one evening soon and get the bark off, a fresh end cut, and seal it. These logs had all been cut for a while.

20260308_134107.webp

20260308_163258.webp
 
Finally used my Alaskan mill for the first time today on some short logs I had picked up, Bois d'Arc & Bradford Pear. It made a small hill of yellow sawdust!

Everything is cut to 3" or 4" thicknesses. Will get it to the bandsaw one evening soon and get the bark off, a fresh end cut, and seal it. These logs had all been cut for a while.

View attachment 285938

View attachment 285939
Congrats on first time use! Looks like you achieved great results! How much time did it take? Chuck
 
Congrats on first time use! Looks like you achieved great results! How much time did it take? Chuck
The first few cuts I was just learning how to get the mill & saw set up for cutting. After I got the hang of it the last couple of logs went quickly. These were all short logs so each cut only took a minute or two.

The chains were milling chains from Granberg and left a much smoother finish on the cuts than I expected to get. This is also the first usage of the 32" bar.

A takeaway is that this 60cc powerhead doesn't have enough umphhh to mill logs the full width of it in tougher woods. One end of the Bradford Pear was close to the max width but it milled easily and quickly. The Osage much less wide was noticeably slower cutting. Not unexpected.

The fuel tank needed filling more often than normal cutting. Also not unexpected.

The chain still seems sharp. I haven't tried to file this angle chain yet. I have 3 more unopened chains so will wait until there are a few more logs cut to mess with it. Hand filing chain isn't my special skill. :cowboy:
 
Last edited:
The first few cuts I was just learning how to get the mill & saw set up for cutting. After I got the hang of it the last couple of logs went quickly. These were all short logs so each cut only took a minute or two.

The chains were milling chains from Granberg and left a much smoother finish on the cuts than I expected to get. This is also the first usage of the 32" bar.

A takeaway is that this 60cc powerhead doesn't have enough umphhh to mill logs the full width of it in tougher woods. One end of the Bradford Pear was close to the max width but it milled easily and quickly. The Osage much less wide was noticeably slower cutting. Not unexpected.

The fuel tank needed filling more often than normal cutting. Also not unexpected.

The chain still seems sharp. I haven't tried to file this angle chain yet. I have 3 more unopened chains so will wait until there are a few more logs cut to mess with it. Hand filing chain isn't my special skill. :cowboy:
You can get or build jigs for sharpening chain saw blades. There are some builds online.
 
You can get or build jigs for sharpening chain saw blades. There are some builds online.
I've got sharpening jigs for regular chain. None will easily accommodate the angle used on the ripping chains. I'll hand file first and get another jig when it's needed.
 
The first few cuts I was just learning how to get the mill & saw set up for cutting. After I got the hang of it the last couple of logs went quickly. These were all short logs so each cut only took a minute or two.

The chains were milling chains from Granberg and left a much smoother finish on the cuts than I expected to get. This is also the first usage of the 32" bar.

A takeaway is that this 60cc powerhead doesn't have enough umphhh to mill logs the full width of it in tougher woods. One end of the Bradford Pear was close to the max width but it milled easily and quickly. The Osage much less wide was noticeably slower cutting. Not unexpected.

The fuel tank needed filling more often than normal cutting. Also not unexpected.

The chain still seems sharp. I haven't tried to file this angle chain yet. I have 3 more unopened chains so will wait until there are a few more logs cut to mess with it. Hand filing chain isn't my special skill. :cowboy:
Your saw is only 60cc? and with a 32" bar? Looks like you're only cutting 12"-14" wide boards, so that's doable with a 60cc saw. 24"-32" wide logs will require a bigger saw.

If you're cutting slabs from firewood length logs then you could have just noodled them free hand with a 20" bar and regular chain like I do. Easier on the chain and more importantly, the saw.

Whether you noodle or slab as you did, CS Milling is hard on the saw's engine. Leave the saw running a minute or so after each cut before you either shut the saw off or resume cutting. This will allow the saw to cool down and help the longevity of the saw's life. And consider using a 40:1 oil mix instead of the standard 50:1 for the same reason.

I use to free hand sharpen my chains, but never could get the rakers at a consistent height. I switched to a Pherd 3 in 1 tool. It's set up for a regular chain, but could be used on a milling chain by just holding the tool at the chain's cutter angle.

And if I told you anything you already know, I apologize; I don't want to sound like a know-it-all. I just don't want you to trash your saw.
 
Your saw is only 60cc? and with a 32" bar? Looks like you're only cutting 12"-14" wide boards, so that's doable with a 60cc saw. 24"-32" wide logs will require a bigger saw.

If you're cutting slabs from firewood length logs then you could have just noodled them free hand with a 20" bar and regular chain like I do. Easier on the chain and more importantly, the saw.

Whether you noodle or slab as you did, CS Milling is hard on the saw's engine. Leave the saw running a minute or so after each cut before you either shut the saw off or resume cutting. This will allow the saw to cool down and help the longevity of the saw's life. And consider using a 40:1 oil mix instead of the standard 50:1 for the same reason.

I use to free hand sharpen my chains, but never could get the rakers at a consistent height. I switched to a Pherd 3 in 1 tool. It's set up for a regular chain, but could be used on a milling chain by just holding the tool at the chain's cutter angle.

And if I told you anything you already know, I apologize; I don't want to sound like a know-it-all. I just don't want you to trash your saw.
i use this https://www.northerntool.com/products/oregon-bench-wall-chain-sharpener-model-410-120-48269
 
Back
Top