What free wood did you find today?


After less than spectacular results from hand filing I watched multiple videos on sharpening. Project Farm on the Tube has a couple that are worth your time and is where I learned about the Timberline system. This gets my normal chains back to new condition and keeps them that way. Its easy to use, quick to set up, has a compact storage case, and gets consistent razor sharp results. The angle is set and does not currently allow for the ripping chain angle. If they come out with an adapter bushing I will buy it.

Since my chainsaw usage is not everyday this more than meets my needs and doesn't require a power cord or a battery.

Screenshot_20260309_084752_Chrome.webp
 
Looks like you live in a typical neighborhood development Jonathan, did your neighbors give you the stink eye?
 
Your saw is only 60cc? and with a 32" bar? Looks like you're only cutting 12"-14" wide boards, so that's doable with a 60cc saw. 24"-32" wide logs will require a bigger saw.

If you're cutting slabs from firewood length logs then you could have just noodled them free hand with a 20" bar and regular chain like I do. Easier on the chain and more importantly, the saw.

Whether you noodle or slab as you did, CS Milling is hard on the saw's engine. Leave the saw running a minute or so after each cut before you either shut the saw off or resume cutting. This will allow the saw to cool down and help the longevity of the saw's life. And consider using a 40:1 oil mix instead of the standard 50:1 for the same reason.

I use to free hand sharpen my chains, but never could get the rakers at a consistent height. I switched to a Pherd 3 in 1 tool. It's set up for a regular chain, but could be used on a milling chain by just holding the tool at the chain's cutter angle.

And if I told you anything you already know, I apologize; I don't want to sound like a know-it-all. I just don't want you to trash your saw.
The 60cc saw has limitations that I am fully aware of. It is the pro model which is supposed to be more robust for everyday extended usage. Time will tell.

The Bradford Pear was 18" - 24" wide and near capacity for my little 32" bar in the mill. This cut fast and well. The Osage was 16"-18" and has been in log form for 3-5 years so a little harder to cut than if it was green. This was noticeable near the ends.

This saw normally wears a 20" bar. This is too short for milling and even noodling for some of the logs after I added an aftermarket set of felling dogs. The stock dogs didn't grip the tree well and the new ones control the cut very well. The 32" bar was purchased for milling only. The only loops that I currently have for it are milling chains.

I've noodled many firewood sized logs and this works well for bowl blanks. It didn't provide the consistency that is needed for boards that the Alaskan mill can do. At least not in my hands. The desire is to make boards for personal use from wood that can be found after a storm in my area. This was the initial trial run of the mill with the short logs on hand.

The intended use is to only work with logs that can be managed by this setup and by myself. When they get bigger the supporting equipment all needs to be bigger, helpers are needed. Material handling equipment needs to be on hand. My space is limited and my body isn't as strong as in its younger days. I'll stay in this size range of wood, after all, a man's gotta know his limitations. :cool:

Greg @woodtickgreg did an excellent write up on chainsaw milling which i have read several times. Thanks, Greg!

There are also a lot of videos on the Tube, some very well done.

Thanks for your input.
 
Last edited:
Looks like you live in a typical neighborhood development Jonathan, did your neighbors give you the stink eye?

Most of my neighbors have been here longer than the 18 years that I have lived here. We know each other well and make allowances for each other as good neighbors do. I'm always the first to offer help when needed and my door gets knocked on for help as well. It works out and have never had a complaint. The noisy tools never get used before 9:00 a.m. nor after 9:00 p.m. Respect for each other goes a long way.
 
Most of my neighbors have been here longer than the 18 years that I have lived here. We know each other well and make allowances for each other as good neighbors do. I'm always the first to offer help when needed and my door gets knocked on for help as well. It works out and have never had a complaint. The noisy tools never get used before 9:00 a.m. nor after 9:00 p.m. Respect for each other goes a long way.
Unless they are 30 and younger. Not all that way, but it only takes one to ruin your day and they are usually from NY, NJ or calipornia. The canadians haven't been here long enough. I've been here a lot longer than all. But one neighbor is close. Now the young'ns think they own the neighborhood and we have an HOA (we don't) and don't mind telling you how things should be. I shut one up, asking if he'd like to pay my bills - then he could tell me what to do! Have also stood there taking vids of their illegal acts. Lot's different than it used to be. Now, I am the only one with tools, knows how to use them, and doesn't mind sweating. Lots of the "Y" chromosome types are useless. Of the couples that even do any yard work, the wife usually does it, except the guy across the street. He's out there about every 4th day scalping his yard. He played minor league baseball in the NE and got used to short grass.
 
Last edited:
Unless they are 30 and younger. Not all that way, but it only takes one to ruin your day and they are usually from NY, NJ or calipornia. The canadians haven't been here long enough. I've been here a lot longer than all. But one neighbor is close. Now the young'ns think they own the neighborhood and we have an HOA (we don't) and don't mind telling you how things should be. I shut one up, asking if he'd like to pay my bills - then he could tell me what to do! Have also stood there taking vids of their illegal acts. Lot's different than it used to be. Now, I am the only one with tools, nows how to use them, and doesn't mind sweating. Lots of the "Y" chromosome types are useless. Of the couples that even do any yard work, the wife usually does it, except the guy across the street. He's out there about every 4th day scalping his yard. He played minor league baseball in the NE and got used to short grass.

Very few here that do any work with their hands. This is a townhouse community, 40% renters these days. Only two others in this hood with any tools that I am aware of, one is a friend and woodworker. The HOA pays a crew to mow grass and all exterior maintenance.

I've been on the HOA board almost the entire time I've lived here. My next door neighbor has also been on it for 6-8 years. If there are any complaints i would know immediately. She and the neighbors on the other side all walked over to see what I was doing yesterday. They both have a key to my house and I for theirs. We watch over each other when we are out of town. All is well there.

These saws have been used extensively after storms to clear driveways and downed trees. The HOA bought the battery powered one for that reason and small trim jobs that don't make sense to call someone for. It has paid for itself in labor savings many times over.
 
Last edited:
In response to your size limitation comment. I have my CSM to handle the stuff that is too big for my sawmill... I have a tiny bandmill but It takes so much work out of milling that I would willingly break down a 40 inch tree to fit on my mill rather than chainsawing it.
 
In response to your size limitation comment. I have my CSM to handle the stuff that is too big for my sawmill... I have a tiny bandmill but It takes so much work out of milling that I would willingly break down a 40 inch tree to fit on my mill rather than chainsawing it.

I totally get that most guys have the chainsaw mill only for the large trees that can't be moved or will not fit on the band mill. This is just a hobby experiment for me. It would be cool to have a band mill, tractors / excavators, large trucks & trailers, kiln, and all of the auxiliaries to move large trees and stacks of wood around but it just doesn't fit my living arrangements or budget. Or my back!

I think it is cool to do this on a small scale with manageable sized wood that I can move alone.

So, @2feathers Creative Making when was the last time that you used that chainsaw mill or the band mill? I can't recall seeing any pictures posted in my 4 years here. :taunt:
:yipee:
 
Last edited:
The 60cc saw has limitations that I am fully aware of. It is the pro model which is supposed to be more robust for everyday extended usage. Time will tell.

The Bradford Pear was 18" - 24" wide and near capacity for my little 32" bar in the mill. This cut fast and well. The Osage was 16"-18" and has been in log form for 3-5 years so a little harder to cut than if it was green. This was noticeable near the ends.

This saw normally wears a 20" bar. This is too short for milling and even noodling for some of the logs after I added an aftermarket set of felling dogs. The stock dogs didn't grip the tree well and the new ones control the cut very well. The 32" bar was purchased for milling only. The only loops that I currently have for it are milling chains.

I've noodled many firewood sized logs and this works well for bowl blanks. It didn't provide the consistency that is needed for boards that the Alaskan mill can do. At least not in my hands. The desire is to make boards for personal use from wood that can be found after a storm in my area. This was the initial trial run of the mill with the short logs on hand.

The intended use is to only work with logs that can be managed by this setup and by myself. When they get bigger the supporting equipment all needs to be bigger, helpers are needed. Material handling equipment needs to be on hand. My space is limited and my body isn't as strong as in its younger days. I'll stay in this size range of wood, after all, a man's gotta know his limitations. :cool:

Greg @woodtickgreg did an excellent write up on chainsaw milling which i have read several times. Thanks, Greg!

There are also a lot of videos on the Tube, some very well done.

Thanks for your input.
Jonathan, I did not know your experience level and apologize for spewing stuff you already knew. I can see you've done this before and know what you are doing.

Good luck and have fun.
 
Jonathan, I did not know your experience level and apologize for spewing stuff you already knew. I can see you've done this before and know what you are doing.

Good luck and have fun.

Dan, No apology needed, I am far from an expert and open to suggestions which is what you offered. This is how we learn. I meant it when I stated, "Thank you for your input!"

My experience with chainsaw milling is limited to what you see in this thread. It's brand new experience but I've done my homework on the concept, equipment, & techniques. I bought quality equipment that was sized to the wood that I intend to work with. Who wants to manhandle 80 pounds of saw / sawmill while trying to cut a straight board?

This equipment was purchased last year at July 4th. It's about time that it got used! Shame on me for letting it sit around for so long! I enjoyed using it and look forward to the next time! :hi3:

@djg
 
Last edited:
So, @2feathers Creative Making when was the last time that you used that chainsaw mill or the band mill? I can't recall seeing any pictures posted in my 4 years here. :taunt:
:yipee:
I actually haven't run the CSM much since getting the mill. The mill is a hobby only mill. I ran about 3 to 4 hundred board foot of live edge cedar last fall and found a warmish day in early winter to mill an oaks stump that had burlish tendencies.
And.... It didn't happen, I know. No pictures. The live edge cedar was sold 2 weeks ago so you can count that one off my list.
I love grabbing a chainsaw and knocking a slice of two off a piece of firewood when I suspect character. I totally agree with your setting, CSM for midsize boards is nice to have. We can hardly afford even the local mills if they dry it.
Oak used to be 500 a thousand... Not anymore
 
I actually haven't run the CSM much since getting the mill. The mill is a hobby only mill. I ran about 3 to 4 hundred board foot of live edge cedar last fall and found a warmish day in early winter to mill an oaks stump that had burlish tendencies.
And.... It didn't happen, I know. No pictures. The live edge cedar was sold 2 weeks ago so you can count that one off my list.
I love grabbing a chainsaw and knocking a slice of two off a piece of firewood when I suspect character. I totally agree with your setting, CSM for midsize boards is nice to have. We can hardly afford even the local mills if they dry it.
Oak used to be 500 a thousand... Not anymore

Just messing with you Frank! :lol2:

I've got nothing but respect for people who get up and put in a full day's work with their hands everyday. :saw:
 
Last edited:
Just messing with you Frank! :lol2:

I've got nothing but respect for people who get up and put in a full day's work with their hands everyday. :saw:
No worries. I got thick skin. And a hard head to go with it. My milling has been seriously delayed by a 'lectric project for an extended family member. But to keep credit where it's due, same family member is planning, weather permitting, to have me mill a bit of "hvbw". This weekend. Maybe the wife will take pictures.
 
Last edited:
Jonathan, I did not know your experience level and apologize for spewing stuff you already knew. I can see you've done this before and know what you are doing.

Good luck and have fun.
What makes this place so special and figured @JonathanH would respond as he did. I learned something from your comments Dan.
 
I finished up on the big pieces of walnut today. Got it all stacked on 'my' log pile.

IMG_7601.webp

Cut off all the fine checking but couldn't remove all the main pith cracks. So, I just sealed and stacked them. Yes, I probably loose some; I just work around the cracks. Got it covered before the rain. Still have 3-4 20" long pieces, but they'll be processed in the next week.
 
Back
Top