Those are nice once you get them set up properly and know what you're doing. On my scale of occasional firewood cutting, they're not in the budget. When my chain dulls, I'm in no hurry, so I just sharpen on the bar. Gives me a rest break too.
Those are nice once you get them set up properly and know what you're doing. On my scale of occasional firewood cutting, they're not in the budget. When my chain dulls, I'm in no hurry, so I just sharpen on the bar. Gives me a rest break too.
The 60cc saw has limitations that I am fully aware of. It is the pro model which is supposed to be more robust for everyday extended usage. Time will tell.Your saw is only 60cc? and with a 32" bar? Looks like you're only cutting 12"-14" wide boards, so that's doable with a 60cc saw. 24"-32" wide logs will require a bigger saw.
If you're cutting slabs from firewood length logs then you could have just noodled them free hand with a 20" bar and regular chain like I do. Easier on the chain and more importantly, the saw.
Whether you noodle or slab as you did, CS Milling is hard on the saw's engine. Leave the saw running a minute or so after each cut before you either shut the saw off or resume cutting. This will allow the saw to cool down and help the longevity of the saw's life. And consider using a 40:1 oil mix instead of the standard 50:1 for the same reason.
I use to free hand sharpen my chains, but never could get the rakers at a consistent height. I switched to a Pherd 3 in 1 tool. It's set up for a regular chain, but could be used on a milling chain by just holding the tool at the chain's cutter angle.
And if I told you anything you already know, I apologize; I don't want to sound like a know-it-all. I just don't want you to trash your saw.

Looks like you live in a typical neighborhood development Jonathan, did your neighbors give you the stink eye?
Unless they are 30 and younger. Not all that way, but it only takes one to ruin your day and they are usually from NY, NJ or calipornia. The canadians haven't been here long enough. I've been here a lot longer than all. But one neighbor is close. Now the young'ns think they own the neighborhood and we have an HOA (we don't) and don't mind telling you how things should be. I shut one up, asking if he'd like to pay my bills - then he could tell me what to do! Have also stood there taking vids of their illegal acts. Lot's different than it used to be. Now, I am the only one with tools, knows how to use them, and doesn't mind sweating. Lots of the "Y" chromosome types are useless. Of the couples that even do any yard work, the wife usually does it, except the guy across the street. He's out there about every 4th day scalping his yard. He played minor league baseball in the NE and got used to short grass.Most of my neighbors have been here longer than the 18 years that I have lived here. We know each other well and make allowances for each other as good neighbors do. I'm always the first to offer help when needed and my door gets knocked on for help as well. It works out and have never had a complaint. The noisy tools never get used before 9:00 a.m. nor after 9:00 p.m. Respect for each other goes a long way.
Unless they are 30 and younger. Not all that way, but it only takes one to ruin your day and they are usually from NY, NJ or calipornia. The canadians haven't been here long enough. I've been here a lot longer than all. But one neighbor is close. Now the young'ns think they own the neighborhood and we have an HOA (we don't) and don't mind telling you how things should be. I shut one up, asking if he'd like to pay my bills - then he could tell me what to do! Have also stood there taking vids of their illegal acts. Lot's different than it used to be. Now, I am the only one with tools, nows how to use them, and doesn't mind sweating. Lots of the "Y" chromosome types are useless. Of the couples that even do any yard work, the wife usually does it, except the guy across the street. He's out there about every 4th day scalping his yard. He played minor league baseball in the NE and got used to short grass.
In response to your size limitation comment. I have my CSM to handle the stuff that is too big for my sawmill... I have a tiny bandmill but It takes so much work out of milling that I would willingly break down a 40 inch tree to fit on my mill rather than chainsawing it.


Jonathan, I did not know your experience level and apologize for spewing stuff you already knew. I can see you've done this before and know what you are doing.The 60cc saw has limitations that I am fully aware of. It is the pro model which is supposed to be more robust for everyday extended usage. Time will tell.
The Bradford Pear was 18" - 24" wide and near capacity for my little 32" bar in the mill. This cut fast and well. The Osage was 16"-18" and has been in log form for 3-5 years so a little harder to cut than if it was green. This was noticeable near the ends.
This saw normally wears a 20" bar. This is too short for milling and even noodling for some of the logs after I added an aftermarket set of felling dogs. The stock dogs didn't grip the tree well and the new ones control the cut very well. The 32" bar was purchased for milling only. The only loops that I currently have for it are milling chains.
I've noodled many firewood sized logs and this works well for bowl blanks. It didn't provide the consistency that is needed for boards that the Alaskan mill can do. At least not in my hands. The desire is to make boards for personal use from wood that can be found after a storm in my area. This was the initial trial run of the mill with the short logs on hand.
The intended use is to only work with logs that can be managed by this setup and by myself. When they get bigger the supporting equipment all needs to be bigger, helpers are needed. Material handling equipment needs to be on hand. My space is limited and my body isn't as strong as in its younger days. I'll stay in this size range of wood, after all, a man's gotta know his limitations.
Greg @woodtickgreg did an excellent write up on chainsaw milling which i have read several times. Thanks, Greg!
There are also a lot of videos on the Tube, some very well done.
Thanks for your input.
Jonathan, I did not know your experience level and apologize for spewing stuff you already knew. I can see you've done this before and know what you are doing.
Good luck and have fun.

I actually haven't run the CSM much since getting the mill. The mill is a hobby only mill. I ran about 3 to 4 hundred board foot of live edge cedar last fall and found a warmish day in early winter to mill an oaks stump that had burlish tendencies.So, @2feathers Creative Making when was the last time that you used that chainsaw mill or the band mill? I can't recall seeing any pictures posted in my 4 years here.
![]()
I actually haven't run the CSM much since getting the mill. The mill is a hobby only mill. I ran about 3 to 4 hundred board foot of live edge cedar last fall and found a warmish day in early winter to mill an oaks stump that had burlish tendencies.
And.... It didn't happen, I know. No pictures. The live edge cedar was sold 2 weeks ago so you can count that one off my list.
I love grabbing a chainsaw and knocking a slice of two off a piece of firewood when I suspect character. I totally agree with your setting, CSM for midsize boards is nice to have. We can hardly afford even the local mills if they dry it.
Oak used to be 500 a thousand... Not anymore


No worries. I got thick skin. And a hard head to go with it. My milling has been seriously delayed by a 'lectric project for an extended family member. But to keep credit where it's due, same family member is planning, weather permitting, to have me mill a bit of "hvbw". This weekend. Maybe the wife will take pictures.Just messing with you Frank!
I've got nothing but respect for people who get up and put in a full day's work with their hands everyday.![]()
That is the same one my brother got 10 years ago for $99. I hand file but after 3 to 5 filings, I use his sharpener to rebalance the chain. Also use it for rakers.
What makes this place so special and figured @JonathanH would respond as he did. I learned something from your comments Dan.Jonathan, I did not know your experience level and apologize for spewing stuff you already knew. I can see you've done this before and know what you are doing.
Good luck and have fun.